Guide · Homeowners · 3 min read · Updated 16 November 2026
Hot Water Cylinder and Loft Tank Removal: A Practical Guide
Short answer
Hot water cylinder and loft tank removal usually follows a switch to a combi boiler. A plumber drains and disconnects the cylinder and isolates the tanks, then the removal team carries the copper cylinder out of the airing cupboard and brings the cold water and expansion tanks down from the loft, cutting them into sections if they will not fit through the hatch. It costs £90–£180.
Why cylinders and tanks are removed
Many UK homes have a conventional heating system, with a hot water cylinder in an airing cupboard, a large cold water storage tank in the loft and a smaller feed and expansion tank beside it. When the boiler is replaced with a combi, which heats water on demand from the mains, the cylinder and both tanks become redundant. Removing them frees up the airing cupboard and clears the loft.
Some homeowners keep the cylinder for a system boiler or a heat pump, which also need hot water storage. Check with your heating engineer before anything is removed.
What needs to happen first
Before collection, a plumber or heating engineer drains the cylinder and isolates the cold water supply to the loft tank. The cylinder is disconnected from its pipework and any immersion heater is electrically isolated and disconnected. The loft tank is drained through its outlet, and any remaining water is bailed out or sucked out with a wet vacuum. Pipe ends are capped or removed.
A full copper cylinder can hold well over 100 litres, so draining it is not optional. Even a small amount of water left in a tank makes it slippery and heavy to bring down a ladder. Lift the lid and check the tank is genuinely empty before the team arrive, and leave any lid or insulation jacket beside it for removal.
- Cylinder drained and disconnected from all pipework
- Immersion heater isolated and disconnected
- Cold water supply to the loft tank turned off
- Loft tanks emptied and pipe ends capped
- Loft boarded or crawl boards laid so the team can move safely
Types of cylinder and tank
Older homes may have any combination of the items below. The material matters for weight, how easy the item is to cut and whether it needs testing before anyone touches it. Old galvanised steel tanks are heavy and often rusty. Plastic tanks are light and flexible. Older cement-like tanks, found in some properties, may be asbestos cement and must be tested before removal.
| Item | Common materials | Removal notes |
|---|---|---|
| Hot water cylinder | Copper, sometimes foam-lagged | Light once drained; scrap value |
| Cold water storage tank | Plastic or galvanised steel | May need cutting to pass through the hatch |
| Feed and expansion tank | Plastic | Small and light once drained |
| Older cement-like tank | Possibly asbestos cement | Must be tested before removal |
| Combination cylinder | Copper with built-in tank | Bulky; may need cutting or a wider route |
Getting tanks out through a loft hatch
Many cold water tanks were placed in the loft before the roof was finished, or squeezed through the hatch when they were newer and more flexible. Decades later, they often will not come back out the same way. Plastic tanks can usually be folded slightly or cut into sections with a saw. Galvanised steel tanks are cut with a reciprocating saw or angle grinder, with care taken to protect insulation and keep sparks well away from timber.
The team uses a stable ladder or loft ladder, lowers sections to a second person below and protects the landing carpet from rust and dirty water. Expect some debris from the loft insulation around the hatch.
Costs
A drained copper cylinder plus cold water and expansion tanks costs £90–£180, including loft access. The price depends on whether the tanks need cutting, the material, how much loft boarding there is and how many flights of stairs are involved. Adding the old boiler costs from £40 for a disconnected wall-hung unit, and radiators start from £10 each.
Copper cylinders have scrap value, which is reflected in the price. If tanks need asbestos testing, that is arranged and priced separately before removal.
After removal
Once the cylinder is gone, the airing cupboard can become storage, a utility space or part of a larger room. The plumber may need to cap or remove redundant pipework under the floor or in the cupboard. In the loft, the space where the tanks stood is often left with a sturdy platform that can be reused for storage, as long as it is in good condition.
Check the loft insulation around the old tank area. It was often left thin or missing under the tank, and topping it up helps the home stay warm.
Preparing the house for collection day
Clear the landing below the loft hatch and move anything fragile from the route between the airing cupboard and the front door. Copper cylinders are light once empty, but they are bulky and easily dented against door frames, and old foam lagging sheds crumbs as it is carried. Lay down old sheets if you are worried about carpets. Make sure the loft light works, or leave a torch by the hatch.
If the plumber is draining the system on the same day, allow time for the water to clear before the removal team arrive. A cylinder that is still half full is far heavier than expected and can spill dirty water on the stairs. A quick message confirming everything is drained and capped means the team can get straight to work and finish in a single visit.
Questions people also ask
Can I remove a loft tank myself?
Only once it is fully drained and isolated, and with care. Tanks are awkward, may be rusty or brittle, and often need cutting to fit through the hatch. Working in a loft also carries a fall risk through ceilings. Old cement-like tanks must be tested for asbestos before anyone disturbs them.
Is an old copper cylinder worth anything?
Yes, copper cylinders have scrap value, though the foam lagging on many must be stripped off first. The value is reflected in our prices. If you take one to a licensed scrap metal dealer yourself, expect payment by bank transfer rather than cash in England and Wales.
Do I need to keep the cylinder if I switch to a combi?
Usually not. A combi boiler heats water directly from the mains, so the hot water cylinder and loft tanks become redundant. Your heating engineer will confirm this. If you are fitting a system boiler or heat pump instead, you will need a cylinder, often an unvented type.
Written and checked by the Boiler Disposal team. Read our editorial policy.
More guides
How Much Does Boiler Disposal Cost in the UK?
Boiler disposal in the UK costs from £40 to collect a disconnected wall-hung combi, system or regular boiler. Floor-standing or cast-iron boilers…
How to Get Rid of an Old Boiler: UK Options Explained
The easiest way to get rid of an old boiler is to have your installer remove it when they fit the new one. Otherwise, you can take a disconnected…
Back Boiler Removal: What Is Involved and What It Costs
Back boiler removal starts with a Gas Safe registered engineer decommissioning the boiler and gas fire, draining the heating system and capping the…
Heating Oil Tank Removal: Costs, Rules and What to Expect
Heating oil tank removal starts with a licensed specialist pumping out any residual oil and sludge, which is hazardous waste needing the correct…
Get a free boiler disposal quote
Tell us what you need and we'll come back with a clear price.
Request a quote